Attaching My Even Feed/Walking Foot

It seriously took me almost an hour today to figure out how to attach my even feed/walking foot to my sewing machine.

Here are the instructions my sewing machine told me (it also had a picture, which was only a little helpful):
1. Raise needle to its highest position.
2. Raise presser bar to its highest position and guide the even feed/walking foot into position from rear of machine with arm on needle clamp.
3. Attach presser bar clamp to presser bar and tighten presser foot screw with screwdriver.

By the way, my machine is a Singer 7467S.

The picture helps a little (especially now that I really know what I'm doing) to figure out what the presser bar clamp and such are but the instructions never said to remove the regular shank, which is absolutely required in order to do step #3.  So I was trying to attach the even feed/walking foot while the regular shank was still attached to the machine, which, obviously, didn't work very well.

Then I found this YouTube video: http://www.youtube.com/watch?v=qVczdRK_K6s. This video tutorial has a lot of information about a lot of different sewing machine feet.  I had to wait until minute 11:30 to get to the even feed section, but it was totally worth it.

Here are my instructions with pictures.

This is the way my sewing machine usually looks.  The regular shank (green arrow) is attached to the machine and the satin foot is attached to the regular shank.

Step One: Turn off the machine.  It may be tempting to keep it on because it will add some light, but don't do it.

Step Two (optional): Remove the foot from the regular shaft by lightly pressing the Foot Release Button (purple arrow). This is optional because if you leave it on it with automatically come off in Step Three.

Step Three: Unscrew the Presser Foot Screw (blue arrow).  In the video I linked to above, they make this look easy but it was not easy for me.  I couldn't use the little screw driver deal that came with my machine, I had to go get a thick, flat head screwdriver to loosen it.  Once the presser foot screw is loose, it is easy to unscrew by hand.

Step Four: Remove the Regular Shank from the Presser Bar (pink arrow).

Step Five: (mostly from the manual instructions) Guide the even feed/walking foot into position from the rear of the machine with the Arm (yellow arrow) on the Needle Clamp (brown arrow) and the Presser Bar Clamp (orange arrow) around the Presser Bar.

Step Six: Screw the presser foot screw back into it's place on the presser bar.

You should now be good to go.

I'm using the Even Feed/Walking Foot to help me quilt some hot pads I'm making.  The hot pads have five layers (outside fabric, muslin for sturdiness, thick batting, muslin, outside fabric) and I wanted to make sure that every layer of my hot pad fed through the sewing machine evenly.  Luckily the Walking Foot is perfect for this kind of task because it has feed dogs on the foot itself.  This means that the feed dogs on the machine are feeding the bottom layers of fabric through the machine at the same time/rate that the feed dogs on the walking foot are feeding the top layers of fabric through the machine.  A perfect combination.

Anyway, I love this foot and I very much wish I had know about it when I made my first quilt but I guess it is too late for that.  Now that I know how to attach it to my machine I hope to get a lot of use out of it.

Recipe: Almond Linguine Florentine

Back when my sisters and I had Sister Dinners, Older Sister made us Almond Linguine Florentine, a recipe she found in our paternal grandmother's cookbook.  CJ and I now have this pasta fairly regularly.

Grandma's note on the recipe: "Daughter" and her boyfriend fixed dinner for my birthday or mother's day.  He did the cooking and this is what he made. Very good!

I agree with Grandma, this is very good.  I don't follow her recipe exactly but it still turns out great.

Original Recipe and Directions:

1 cup chopped onion
3 Tbsp butter or margarine
3 Tbsp vegetable oil
3 Tbsp flour
3/4 tsp thyme
      salt and pepper to taste
1 can beef broth
3/4 cup whipping cream
3 Tbsp Dijon-style mustard
1/2 pound cooked ham, cut into strips
3/4 cup chopped parsley
3/4 cup toasted slivered almonds
1/2 pound cooked linguine noodles

In skillet saute onions in butter and oil until limp.  Blend in flour and seasonings; cook and stir over low heat until flour is well blended.  Gradually stir in broth and cream; cook and stir over medium heat until mixture thickens, about 5 minutes.  Stir in mustard, ham, parsley and almonds.  Toss hot linguine with sauce; serve on a bed of fresh spinach leaves.  Garnish with additional chopped parsley and almonds.

My Version:

1 cup chopped onion (or however much I have on hand if I even have some on hand; in the pictures for this blog I didn't use onion because I didn't have any)
3 Tbsp butter or margarine or vegetable oil (why use 6 Tbsp of fatty stuff when you can use only 3?)
3 Tbsp flour
3/4 tsp thyme (in all honesty, I don't usually measure herbs)
     pepper to taste (I leave out the salt because I figure the ham is going to be salty enough)
1 cup beef broth (I use bouillon cubes instead of canned and I don't know how many cups are in a can anyway)
3/4 cup whipping cream
1/2 pound cooked ham, cut up
3/4 cup slivered almonds
1/2 pound cooked noodles

My directions are pretty much the same as Grandmas:

Melt butter (with onion if using onion), add flour, thyme, and pepper, stir until well blended.  Add beef broth and cream, stir.  Let sit on medium heat, stirring occasionally, until thickish.  Add ham and almonds, stir.  Mix sauce with cooked noodles.

Serve however you like.  I think green beans are good with this pasta and I think diced tomatoes are good with just about any pasta.

Enjoy!

Birthday Board

Here's another find from Pinterest: a Birthday Board.  When I first saw this I thought it would make a great Mother's Day gift, so I pinned it and decided I would make it for my mom for Mother's Day.  Then Mom also pinned it and mentioned that she was going to make one for herself, so I had to tell her that I was going to make it for her.  I would have liked for it to be a surprise but this worked out alright because I was able to borrow paint from her that matched her walls.

I didn't keep my receipts from this project but the whole thing (including materials I didn't end up using because of a mess up) cost about $30.

Materials Used:
- Background Board.  Make sure it is large enough to fit 12 small dowels for each month and whatever text you want to put on it.  Make sure it is small enough to put wherever you want to put it.

- Text.  I couldn't find letters in the exact size I wanted so I also bought round dowels to put behind the text.

- Month and Day Dowels.  Make sure you have enough to have one for each month (Jan - Dec) and one for each birthday plus extras for an expanding family.  This is where my mess up happened but I'll get into that in a little more detail later.

- Hooks and Eyes.  Really you can attach you birthdays anyway you want but I wanted to use hooks and eyes so it would be easy to add new birthdays.  Make sure to get enough hooks for every month and day dowel and enough eyes for just the day dowels.

- Paint.  You'll need paint for the background board, the text on the background board, and the dowels but you'll also need a paint pen to add names and birthdays to the day dowels.

- Paint Brushes.  I had three but wished I had more because the paint dried faster on the dowels that the paint brushed dried after being cleaned.

- Hot Glue and Hot Glue Gun.  If there is a better way to attach everything to the board, by all means use that.

- Hanger.  I don't remember what this is really called but you'll need a thing to put on the back of the board so it can be hung on a wall.  I have a picture of one later on if I'm not being clear here.

Steps
1.  Paint everything that needs painting.
2.  (Optional) Glue text onto background dowels.
3.  Glue text/background dowels on to background board.  In the picture this looks really pretty with it being centered and all but the truth is, I wish I had glued them just a little higher on the Birthday Board.  From the first picture in the post you can see that the month dowels are really close to the text.  If I had glued the text higher, their wouldn't be so much empty space at the top of the Birthday Board and the whole thing would just look better.

Here are my side steps because of how I messed up.  The month and day dowels that I bought weren't thick enough for the hooks and eyes that I bought.  Dad was going to help me drill holes in the dowels for the hooks and eyes but we kept breaking the dowels.  So we went to the hardware store, bought some MDF and a hole saw (Dad had been looking for an excuse to buy one) and we cut out the dowels ourselves.  The side steps are for that process.

S1. Cut out dowels using the hole saw.  Make sure the saw is set up in a way that you won't be getting a hole in the middle of your dowel.
S2. The dowel won't be perfect, so sand off any awkward edges.
S3. Paint (see Step 1).  Painting these wider dowels was much easier than the thin ones because I didn't have to worry about getting paint everywhere.

Now back to the regular steps.

4.  Make a hole in the dowel in which to put the hooks and eyes.  Because my dowels were made from MDF, I could just use a push pin to make the holes.  If your dowels are made of something a little thicker, you may want to use a drill.  Remember that you month dowels only need one hole.
5.  Screw in hooks and eyes.  I used pliers (CJ's idea) to help screw in the hooks and eyes, it really ended up being easy after step 4.
6.  Use the paint pen to add names and days to the day dowels and the months to the month dowels.
7.  Screw the hook to the back of the board.  I also glued it on there, just to be safe.

Now, once all the days are hooked in the right order, you have a Birthday Board.

That Was Easy

I would just like to take a second to thank my sewing machine for making it really, really easy to put a blanket stitch on my niece's fleece blanket birthday gift.  I simply chose the setting and sewed.  All the way around 2 yards of fleece took about 20 minutes.  I don't think it could have been easier.